Can a mirror labeled IP44 be installed anywhere in the bathroom? No: before comparing shapes and functions, you must locate its position relative to the shower or bathtub. To choose an LED bathroom mirror, the right question is first about permitted installation, then about comfort in front of the basin.
In short: the choice depends on the electrical zone, the light actually received by the face and the fixing conditions. A touch or anti-fog function does not replace any of these checks.
Identify the electrical zone before choosing the mirror
Where will the mirror be placed relative to the bathtub or shower? The presence of a basin underneath is not enough to answer. The electrical standard applicable to rooms containing a bathtub or shower divides the room into safety volumes: volume 1 rises to 2.25 m above the bottom of the bathtub or tray, and volume 2 adds a 60 cm band around this volume. These distances are measured from the edges of the tray or bathtub, and it is these edges that define the volumes.
Read the volumes before the IP rating
Each volume corresponds to requirements on the minimal expected IP rating, the allowed type of supply and the residual-current protection. This initial identification must be cross-checked with the electrical class and the product manual to decide on the installation location.
| Zone | Measurement reference | Expected IP rating (general reference) | Supply |
|---|---|---|---|
| Volume 0 | Inside the bathtub or tray | IPX7 for permitted devices | Safety extra-low voltage (SELV), only for permitted devices |
| Volume 1 | Up to 2.25 m above the bottom of the bathtub or tray | IPX4 minimum, IPX5 if the location is subject to water jets | SELV possible under admission conditions |
| Volume 2 | 60 cm band around volume 1 | IPX4 minimum | According to electrical class and authorized equipment |
| Outside volumes | Beyond this band | According to the product manual | According to the manual and circuit protections |
SELV means safety extra-low voltage. The IP rating describes the enclosure protection against solids and liquids. The electrical insulation class, the connection method and the location of the supply depend on the product technical documentation and must be checked before installation.
Take the useful measurements
The survey covers the mirror position, the cable outlet and the LED driver housing. A dimensioned sketch and a photo of the walls help the electrician read the configuration.
- Distance to bath or shower: note the distance from the edges of the bathtub or tray.
- Actual geometry: indicate a walk-in shower, a fixed screen or jets likely to reach the location.
- Device identification: note the IP rating and the electrical class in the manufacturer's technical documentation; a commercial mention of humidity resistance is insufficient.
- Driver position: identify where the box that powers the LEDs will be placed and how it will remain accessible once the mirror is fixed.
Decision point: distance, IP rating, insulation class and supply location must be compatible together. A single one of these elements is not enough to conclude.
Types of LED mirrors and functions to check
Two mirrors described the same way can require different installations: one can be screwed above a basin, the other require a niche and flush wiring. The main criterion remains the useful light for the face: delivered flux, beam direction and color rendering.
| Type | Typical use | Point of vigilance | Installation to check |
|---|---|---|---|
| Wall LED mirror | Frontal face lighting above a basin | Distance to water volumes and mounting height | Load-bearing support and cable route |
| Recessed mirror | Medicine cabinet or niche | Useful depth and cable passage | Cutout, clearances prescribed by the manual and access to the driver |
| Freestanding mirror | Placed on furniture | Stability and cord length | Location of the outlet and cable safety |
| Anti-fog mirror | Ready for use after the shower | Treated surface, activation mode and power supply of the heater | Connection according to the manual |
| Mirror with outlet | Razor or hair dryer | Accepted appliances and authorization in the concerned zone | Connection by a professional according to the zone |
Check each function on the product sheet
The anti-fog acts only on the glass area covered by the heater: check the treated surface, the activation mode and any separate supply. A touch control describes the control mode; check the sheet to see if operation with wet hands is explicitly mentioned. For integrated outlets, check the accepted appliances and the authorization of that location according to the electrical zone.
Flux, color temperature and color rendering
After checking the volumes, the evaluation becomes photometric. Watts measure consumption. Comfort in front of the mirror is read in lumens, beam direction and color rendering index (CRI).
Compare separately: total flux (lumens), portion of flux directed to the face, color temperature (kelvins) and CRI. A homogeneous diffuser limits shadows; a too directional source can leave under-chin areas or around the eyes insufficiently lit.
| Criterion | Question to ask before purchase |
|---|---|
| Luminous flux | Does the value concern the entire luminaire and what part actually lights the face? |
| Color temperature | Which tones are available and is there a neutral setting suitable for makeup? |
| CRI | Is the value indicated for this model? |
| Diffusion | Is the light homogeneous or does it create annoying shadows? |
An ambient photo illustrates the decorative effect; it does not demonstrate the quality of lighting obtained at the usual face distance.
Dimensions and MPDiscount catalogue models
Note the clear width, the height above the washbasin, the position of the faucet and the swing of neighboring furniture. A paper template temporarily fixed to the wall allows judging the actual footprint.
Consult the MPDiscount mirror collection to search for a compatible format: https://mpdiscount.com/collections/miroirs.
Examples of references listed on MPDiscount:
- LED wall mirror full length 160×59 cm — 3 temperatures — bronze frame (format and functions indicated; check the IP rating, photometry and connection conditions in the technical documentation).
- LED wall mirror round 89 cm — engraved wave bands — 3 temperatures — black aluminum frame (diameter 89 cm; check the IP rating and photometric values in the technical documentation before approving bathroom installation).
Test the format in the room
A round 89 cm format or a full length 160×59 cm model can be suitable depending on use; test the actual standing position and the distance to the mirror. For a double basin, consider the distribution between stations and the mounting orientation provided by the manufacturer.
- Faucets: keep access to the controls.
- Neighboring furniture: check door openings.
- Electrical outlet: ensure it can reach the connection without an improvised visible cable.
Fixing: screwing, adhesive or supplied device
An LED mirror combines glass, weight and electrical supply. The installation method is stated in the product manual: screwing, bonding or supplied device, as well as the load to be borne. On plasterboard, use a suitable anchor; on a solid wall, a sized expansion fixing. Bonding should only be improvised if the manual provides for it.
- Read the product manual.
- Identify the substrate and choose anchors according to the announced weight.
- Locate services before drilling.
- Mark and drill while protecting tiles if necessary.
- Check the hanging before powering on.
- Entrust the connection to an electrician.
Do not transpose rules applicable to other decorative or acoustic panels without checking the specific mirror manual.
Checklist before ordering
- Measured location: sketch showing mirror, shower/bath, walls and cable outlet.
- Protection identified: IP rating and electrical class noted on the sheet or nameplate.
- Documented supply: type of connection and driver position (integrated or remote).
- Comparable lighting: luminous flux, CRI and available color temperatures.
- Included functions: controls, offered settings and anti-fog power supply if present.
If a product sheet is incomplete, request the technical documentation before ordering. Price, stock, delivery, warranty and return information should be checked on the MPDiscount product page at the time of purchase.
MPDiscount offers mirrors and layout equipment for private and professional customers. To prepare this purchase, consult MPDiscount and have the location and connection validated by an electrician using the technical documentation provided for the chosen reference.




